MF860 |
|
|
-
Use your tractor to mulch large areas of brush
and felted tops with out lifting a twig. direct drive to give
you ultimate cutting power!
-
126 carbide tipped
teeth for longer tooth life, smoother operation and finer mulch.
-
Direct drive to give you ultimate cutting power!
-
Teeth can be field installed.
-
Pusher bar to push trees away from mulcher as
they are cut
-
Rugged timer belt for long durability.
-
Unit weight 1550 lb
-
Cutting width 60"
-
Over all width 75"
-
Overall Height 58"
|
|
|
|
Drive System on Tractor |
|
45 hp |
60 hp |
65 hp |
70 hp |
Regular Drive |
3" |
4" |
5" |
6" |
Creeper Gear |
5" |
6" |
7" |
8" |
Automatic Transmission |
8" |
10" |
12" |
14" |
Double All Sizes For Intermittent
Cutting |
|
|
Mulcher Teeth |
|
|
-
On the picture to the left you can see that these
mulcher teeth are staggered in a spiral
-
Rotating teeth are populated in a three contact
pattern every half round allowing a smooth transition of power,
teeth do not all hit in banks as it may appear.
-
This staggered pattern along with knife tipped
teeth finally allows low-flow mulching to become a realized reality.
-
Teeth bit deep with a significant cutting angle
design
-
Ultra tooth population reduces “impact per tooth”
on stones permitting little or no replacement of teeth.
-
Replacement of teeth is done in ones or two’s,
“never” as a set.
-
Low maintenance cost by design, replace only the
tips, “not” big blocks of steel.
|
|
Comparison Table |
|
MF360 |
MF548 |
MF760 |
MF860 |
Motor option available |
A450,B550 &C350 |
A450&B550 |
C350 |
|
Path width |
70 |
62 |
75 |
75 |
Rotor width |
60 |
48 |
60 |
60 |
Cutting height from ground |
2.5" |
0 to 1.5" |
0 to 1.5" |
0 to -1.5" |
Rotor rpm |
800 |
1200 |
1750 |
1800 |
Number of cutters |
2 |
104 |
126 |
126 |
slashes per second |
2600 |
4160 |
7350 |
7560 |
Hitch type |
skid steer |
skid steer |
skid steer |
3-point |
Hitch size |
universal |
universal |
universal |
CAT II |
Max
psi |
3000 |
3000 |
3000 |
3000 |
Max
flow (GPM) |
24 |
24 |
42 |
20 |
Recommended flow (GPM) |
22 |
22 |
40 |
10 |
Min
flow (GPM) |
10 |
12 |
20 |
2 |
Hose
size |
3/4" |
3/4" |
1" |
1/4" |
Max
HP |
check flow and psi |
check flow and psi |
check flow and psi |
70 |
Min
HP |
40 |
35 |
60 |
45 |
System protection |
built in relieve |
built in relieve |
built in relieve |
slip clutch |
Needs case drain |
check motor option |
yes |
no |
Shipping size (lenth, width, hight) |
36x80x90 |
64x36x40 |
80x48x65 |
80x48x65 |
Unit
weight (lb) |
1240 |
1290 |
1800 |
2100 |
|
|
|
Motor Option |
A450 |
B550 |
C350 |
Max
psi |
3000 |
3000 |
3000 |
Max
flow (GPM) |
20* |
24* |
40* |
Recommended flow (GPM) |
12-20 |
12-24 |
22-40 |
Min
flow (GPM) |
10 |
12 |
20 |
Hose size |
3/4" |
3/4" |
1" |
Must have case drain |
no |
yes |
yes |
* Motor will be destroyed if this value is exceeded |
|
|
|
A450 MOTOR |
HYDRAULICS |
OPERATION |
12 GPM |
15 GPM |
18 GPM |
20 GPM |
21 GPM |
2500 PSI |
Steady forward |
0.75" |
1" |
1.25" |
1.5" |
N/A* |
3000 PSI |
Steady forward |
1" |
1.25" |
1.5" |
2" |
N/A* |
Double tree size for "stop & crawl" cutting. |
B550 MOTOR |
HYDRAULICS |
OPERATION |
12 GPM |
20 GPM |
22 GPM |
24 GPM |
25 GPM |
2500 PSI |
Steady forward |
0.75" |
1.5" |
2" |
2.25" |
N/A* |
3000 PSI |
Steady forward |
1" |
2" |
2.25" |
2.5" |
N/A* |
Double tree size for "stop & crawl" cutting. |
C350 MOTOR |
HYDRAULICS |
OPERATION |
22 GPM |
24 GPM |
30 GPM |
40 GPM |
41 GPM |
2500 PSI |
steady forward |
2" |
2.25" |
3" |
3.5" |
N/A* |
3000 PSI |
steady forward |
2.25" |
2.5" |
4" |
4.5" |
N/A* |
Double tree size for "stop & crawl" cutting. |
MF860 3-PTH PTO DRIVE |
GEAR
SELECTION |
OPERATION |
45 HP |
50 HP |
60 HP |
70 HP |
71 HP |
Low Gear |
steady reverse |
1" |
1.5" |
2" |
3" |
N/A* |
|
stop and go |
2" |
3" |
4" |
5" |
N/A* |
Creeper |
steady reverse |
2" |
3" |
4" |
5" |
N/A* |
|
stop and go |
3" |
4" |
5" |
6" |
N/A* |
Hydrostatic |
steady reverse |
4" |
5" |
6" |
8" |
N/A* |
|
|
|
|